airsoftieftin.ro Web analytics

Categorii

Ascu2 Generatia a 4-a pentru V2

Ascu2 Generatia a 4-a pentru V2
: 756 Producător: Airsoft Systems
Cod produs: 19475
Puncte de recompensă: 10
Disponibilitate: În Stoc
399 Lei
Cant: Adaugă în Coş
Adaugă in Wishlist Compară produs
Telefon : 0722.434.908 / 0722.603.319 / 0762.853.111

ASCU2 Generatia a 4-a pentru Gearbox V2

La cerere efectuam montaj in service specializat 

ASCU2 gen.4 for GearBox v.2

The ASCU is a two-part electronic module ( the control module and the sensor module ) which, upon being installed in the Airsoft replicas, significantly improve their operation. The traditional joint module was replaced with a sensor module which monitors the actual position of the piston thread-wheel, the firing mode selector lever and the trigger. The gathered information is sent to the control module – in which the software located in the processor analyzes it and controls the replica’s motor with the use of the MOSFET active break.

The ASCU improves the operation of a V.3 gearbox and makes that the replica equals the more expensive replicas and the more sophisticated PTW class replicas. The ASCU system monitors the operation of the replica no matter the speed of squeezing the trigger and is responsible for the full cycle of the piston’s operation, both in the semi-automatic and full automatic firing modes. The piston stops in the starting position after each shot.

The ASCU is equipped with the Low Drain Protection system which is specially designed to secure the lithium-polymer (LiPo) batteries from being damaged.

In case of any emergency, the ASCU stops the firing mode in the replica and, therefore, secures the inner elements from further damage.

The ASCU is easy to install in the replica which is equipped in the V.3 gearbox. Most of the models does not require the modification of the airsoft rifle’s original parts. Yet, in some cases, some minor changes may have to be introduced – thanks to this the installation process will be completed without any problems.

The control unit  is very small and may be placed in the stock or in the front grip (6,5cm x 1,6cm x 1,4cm), while as the second sensor unit fully replaces the connection module and the wiring.

The sensor unit  monitors the operation of the piston thread-wheel and thanks to this the whole system is capable of making a full cycle of the gearbox operation (the BB pellet will never remain in the barrel upon removing the magazine and the main spring will always be lose when the replica is not used).

The ASCU module is adapted to operate with more sensors which will not allow to place a shot when the magazine is empty and, in the case of the “M” replica series, it will make the user use the magazine catch lever whenever the magazine is replaced with a new one.

  • The module improves the trigger’s reaction time of the AEG replica, which in comparison to the classic module is practically instant.
  • It prevents from an accidental double shot: when the next trigger squeeze is faster than the human reaction – each trigger squeeze is one shot.
  • It allows to shoot a 3 round burst by squeezing the trigger shortly in the full-auto firing mode.
  • The easy to install module replaces the connectors and the anti-reversal in any V.3 gearbox which’s application eliminates the jamming of the piston. Moreover, it guarantees that the replica will always make a complete cycle (the main spring will remain in the lose position).
  • The ASCU controls the battery charge level and does not allow it to discharge too excessively what is very important whenever using lithium batteries (LiPo, LiIon, LiFe).
  • The module scans for problems and malfunctions and informs about it with a sound and vibration and, also, cutting off the power source what prevents from further damage to the gearbox.
  • Cooperating with the dedicated HU chamber, the module eliminates a blank shot in the replicas equipped with an operating bolt catch – this means that it is impossible to shoot when the magazine does not feed the replica with BB pellets.
  • The ACSU unit significantly extends the battery’s lifespan.
  • It gives more possibilities than the Systema Revolution and the PTW at smaller installation costs and allows to use a wide range of spare parts which are available for the V.2 and V.3 gearbox.
  • The product is granted with a 24-month warranty; only in the case when it is installed by an authorized service.

What's new in Gen.4 version?

1. New MosFet transistors with 16 times less resistance, resulting in to faster cycle, better active brake, more shots per battery charge and less heat.
2. New very strong trigger switch.
3. New reinforced design with full polymer encasing.
4. Better short-circuit protection.
5. Easier installation.
6. Updated software with easier programing (accidental hop-up program activation is impossible).
7. Improved cut-off lever.
8. Improved selector plate.
9. Fits all standard and reinforced version 2 gearboxes.
10. 3 year world wide warranty.

Nu sunt opinii despre acest produs.

Spune-ţi opinia

Numele tău:


Opinia ta: Notă: Codul HTML este citit ca şi text!

Nota: Rău           Bun

Introduceţi codul din imagine:



ASCU2 Generatia a 4-a pentru Gearbox V2 La cerere efectuam montaj in service specializat  ..
399 Lei

Baza de montare pentru Glock 18C AEP Compatibil cu modelele Cyma sau ASG.   &n..
95 Lei

Magazie capacitate marita compatibila cu Glock 18C electric. Capacitate: 100 bile   ..
60 Lei